PLAN REV 1.2MILESTONES 14COMPONENTS 26UPDATED 2026-11-17LICENSE CC BY-SA 4.0
C06.2 · Component of M06

Ice mining and water extraction plant

Cold-rated excavators dig icy regolith inside a permanently shadowed crater, heat it in a sealed oven, and catch the water vapour on a cold trap. The water is cleaned and stored for drinking, fuel cells and propellant.
Sub-components · 6
1

Cold-rated excavator

Removes the dry top layer and digs icy regolith in the dark at 50–120 K.

  • Counter-rotating bucket drums
  • Heated electronics box
  • Wheels and drive motors rated for cryogenic temperature
  • Lights, lidar and cameras
  • Battery and tether option
BASIS: NASA RASSOR; Break the Ice Lunar Challenge rovers (2024) · TRL 4
2

Haul and transfer

Moves icy regolith to the oven and spent regolith back to the pit; carries water out of the crater.

  • Regolith hopper
  • Water tanker vehicle
  • Insulated water tank
  • Dust-tolerant fluid coupling
BASIS: NASA polar water case study (2 tankers); KSC dust-tolerant umbilical · TRL 4
3

Sealed heating chamber (oven)

Heats icy regolith in a closed volume so the ice turns to vapour and does not escape to vacuum.

  • Auger dryer with heated casing
  • Inlet and outlet seals or lock
  • Heaters (electric or waste heat)
  • Temperature and pressure sensors
  • Spent regolith chute
BASIS: Auger dryer modelled in NASA case study; lab breadboards · TRL 3
4

Cold trap

Freezes the water vapour onto cold plates as ice, then warms to release it as liquid or move it as ice.

  • Cold plates or finned condenser
  • Radiator to the PSR sky
  • Defrost heaters
  • Non-condensable gas vent
BASIS: NASA thermal mining and frost-deposition tests · TRL 4
5

Purification

Removes dissolved gases, dust and trace metals so the water is safe to drink and to electrolyse.

  • Degassing step (CO, CO₂, NH₃, H₂S, CH₄)
  • Particle filters
  • Ion-exchange or sorbent beds for metals including mercury
  • Distillation stage
  • Conductivity and pH sensors
BASIS: Terrestrial water treatment; ISS water processing heritage · TRL 4
6

Water storage

Holds clean water above freezing near the base and hands it to C06.3 and the M04 fuel cells.

  • Aluminium tanks
  • Heaters and insulation
  • Level and quality sensors
  • Transfer pump
BASIS: Standard spacecraft water tanks · TRL 6
Engineering notes

What it does

Ice is trapped in the cold, permanently shadowed regions (PSRs) near the poles. The LCROSS impact into Cabeus crater found water ice at about 5.6 ± 2.9% by mass in the regolith4. This plant digs that icy soil, heats it, captures the water and cleans it. Water gives drinking supply, fuel-cell storage for M04 and, once split, hydrogen and oxygen.

How it works

This plan follows the architecture of a NASA case study. Excavators work in the PSR. Water is extracted at the mine and carried out of the crater by tankers to a sunlit ridge1.

Excavator. The NASA study used RASSOR, a dual bucket-drum excavator1. In NASA’s Break the Ice Lunar Challenge (June 2024), the second-place rover used a drum scraping tool to mine, collect and haul material2. The study assumed PSR surface temperatures between 50 K and 120 K1.

Oven. Icy regolith is heated so the water leaves as vapour. The NASA study modelled an auger that moves regolith through a heated casing, with 75% extraction efficiency1. The chamber is sealed so vapour goes to the cold trap, not to vacuum.

Cold trap. Vapour freezes onto cold plates. In the NASA study, extracted water is frozen into a tank on a mobile tanker1.

Purification. LCROSS and LRO found that up to 20% of the material thrown up by the impact was volatiles. These included methane, ammonia, hydrogen, carbon dioxide and carbon monoxide, plus light metals such as sodium and mercury3. Sulfur-bearing species and light hydrocarbons were also seen4. The NASA study did not yet include water clean-up1. This plan adds degassing, filtration, sorbent beds and distillation.

Transfer and storage. The NASA study used a dust-tolerant automated umbilical for fluid transfer1. NASA KSC has built and demonstrated an automated interface for fluids, power and data, designed against regolith dust5.

Sizing

The NASA baseline: 15 t of water from regolith with 5% water and 75% extraction needed 398 t of regolith, a 32 m × 32 m mine 30 cm deep, and 22 kW at the mine, over 225 days of production1.

This pilot (ESTIMATE, same assumptions):

Item Working Result
Regolith 10 t ÷ (0.05 × 0.75) 267 t/yr
Volume 267 t ÷ 1.3 t/m³1 205 m³
Mine area at 30 cm 205 ÷ 0.3 684 m² (~26 m × 26 m)
Mine power 22 kW × (10 ÷ 15), same 225 operating days ~15 kW

The NASA study found that at 1% water the extraction system no longer scales well1. If M01 measures less than about 3%, this plant should be resized before flight.

Testing and qualification

  1. Test each part at 50–120 K in a thermal-vacuum chamber with icy simulant.
  2. Run the oven and cold trap together in vacuum. Measure recovery, energy per kg and seal leakage.
  3. Add known amounts of CO, NH₃, H₂S and mercury to the simulant and prove the purification removes them.
  4. Drive the excavator and tanker over a 5 km course with 16° slopes, as in the NASA study site1.
  5. On the Moon, start with short excursions from the crater edge, then extend run time. Publish yield and contaminant data.

Open questions

  • What is the real ice content and depth at the chosen PSR? (M01)
  • Should water be carried out as ice or as liquid?
  • Can waste heat from the power system heat the oven, to save electricity?
  • How much mercury and sulphur is in the water, and which purification stage removes it best?
  • How fast does dust wear the oven seals?
Problems and solutions · 8
SeverityProblemSolution
CriticalNo ice deposit suitable for mining has been located yet; the real ice content may be far below 5%Site the plant only from M01 drilling data; oxygen-from-rock (C06.1) covers breathing oxygen if ice fails
HighElectronics, lubricants and seals must work at 50–120 KKeep electronics in heated boxes; use dry lubricants; test at temperature in a thermal-vacuum chamber
HighLCROSS saw CO, NH₃, CH₄, H₂S and mercury with the water; some are toxicMulti-stage purification and testing of every batch; vent or capture gases as by-products
HighAbrasive dust wears oven seals and lets vapour leakReplaceable seals; measure leak rate; design the oven so a leak lowers yield instead of stopping it
MediumA dry top layer of unknown depth must be removed firstMeasure overburden with M01 drilling; size excavator time with margin
MediumMany round trips into and out of the crater wear vehiclesLarger water tanks to cut trips; plan maintenance at the sunlit base
MediumCold trap fills unevenly and loses capture efficiencySeveral smaller traps cycled in turn; measure deposit rate in ground tests
MediumNavigation and communication in permanent darknessLidar and lights on vehicles; M03 relay at the crater rim

Specification

Output target10 t of purified water per year
Assumed ice content5% by mass, 75% extracted (NASA study assumptions)
Regolith to process~267 t per year (ESTIMATE)
Mine area~26 m × 26 m per year at 30 cm depth (ESTIMATE)
Working temperaturePSR surfaces 50–120 K (NASA study assumption)
Power at mine~15 kW (ESTIMATE, scaled from NASA study)
Mass~3 t including excavator (M06 ESTIMATE)
Haul distance~5 km each way, slopes ~16° (NASA study site)
Delivery classMedium lander
Technology readiness · TRL 4 / 9

Sources

  1. Kleinhenz and Paz, NASA: Case study for lunar ISRU systems utilizing polar water (ASCEND 2020) (Nov 2020)
  2. NASA: California teams win $1.5 million in NASA's Break the Ice Lunar Challenge (Jun 2024)
  3. NASA: NASA missions uncover the Moon's buried treasures (LCROSS and LRO results) (Oct 2010)
  4. Colaprete et al., Science: Detection of water in the LCROSS ejecta plume (Oct 2010)
  5. Townsend, Mueller and Tamasy, NASA KSC: Dust tolerant commodity transfer interface mechanisms for planetary surfaces (Oct 2014)
ProjectOPEN MOON · Self-sustaining lunar colony
DocumentC06.2
Revision1.2 · Draft
EditEdit on GitHub