PLAN REV 1.2MILESTONES 14COMPONENTS 26UPDATED 2026-11-17LICENSE CC BY-SA 4.0
C05.2 · Component of M05

Hardened landing pad

A prepared, fused-regolith surface with a compacted apron and an ejecta berm, so landers can touch down and lift off without blasting dust and rocks across the base.
Sub-components · 5
1

Sub-grade preparation

Excavators clear rocks, level the site and compact the loose top layer so the fused surface sits on a firm base.

  • Rock clearing and survey
  • Grading to a level surface
  • Compaction passes
  • Drainage-free cross-slope check by lidar
BASIS: IPEx-class excavators (C05.1); PISCES robotic site grading · TRL 4
2

Fused surface (sintered or pavers)

The core is fused regolith, either laid in place by the C05.3 robot or as interlocking pavers with grouted joints.

  • In-place laser or microwave fused layers
  • Interlocking sintered pavers
  • Regolith-polymer grout for joints
  • Compacted outer apron
BASIS: NASA/Masten hot-fire tests of sintered pavers; ICON laser VMX · TRL 4
3

Edge and ejecta berm

A ring of piled regolith stops low-angle spray that leaves the pad.

  • Piled regolith berm
  • Sintered or bagged berm crest
  • Gaps for road access, offset so there is no line of sight to the base
BASIS: NASA KSC pad concepts (blast barriers) · TRL 3
4

Landing markers and lighting

Passive and active markers help the lander's navigation system find the pad centre in low sun or darkness.

  • Radio beacon at pad centre
  • LED edge lights on the grid
  • High-contrast reflective markers
  • Pad survey map shared with lander providers
BASIS: Plan design choice; no lunar pad aids have flown · TRL 3
5

Inspection and repair

Cameras and witness plates measure what each landing does; robots fix damage between landings.

  • Stereo cameras on the berm (SCALPSS-type)
  • Witness plates at 100 m, 500 m and 1 km
  • Post-landing lidar scan of the surface
  • Repair kit: pavers and polymer grout
BASIS: SCALPSS (flew on Blue Ghost Mission 1) · TRL 5
Engineering notes

What it does

A rocket plume on bare regolith erodes the surface and throws particles out at high speed. These particles obscure sensors, crater the ground under the lander, and hit nearby equipment3. In 1969 Apollo 12 landed 155 m from Surveyor III. A NASA analysis found that small dust particles could reach Surveyor at up to 130 m/s4. A pad gives a known, firm surface that makes little ejecta. A barrier around it catches what does escape3.

How it works

NASA KSC splits a pad into a central zone for normal landings, an outer perimeter for off-target landings and dust control, and blast barriers3. Open Moon follows that layout.

Sub-grade. Lunar regolith is loose at the top. Its bulk density is about 1.30 g/cm³ at the surface, rising to 1.92 g/cm³ below 1 m10. It also compacts less than simulants on Earth8. So C05.1 excavators clear rocks, level the site and compact it before any fusing. In 2015 the PISCES team in Hawaii, working with NASA Swamp Works, used a rover to grade a site and lay 100 basalt pavers7.

Fused surface. NASA and Masten hot-fire tested sintered basalt pavers, carbon fibre blankets and regolith-polymer pavers2. They used a 444 N methane-oxygen engine. Erosion was heavy under the most extreme thermal case, but every test article stopped regolith ejecta1. One test had nine sintered pavers with polymer grout in the joints1. ICON’s laser-fused regolith reached about 50,000 psi compressive strength. Its density is 2.7 g/cm³9. Open Moon fuses the core with the C05.3 robot. It lays pavers where joints are needed.

Berm. A ring of piled regolith around each pad blocks low-angle spray. Road gaps are offset, so no straight path leads from the pad centre to the base.

Markers and lighting. Pad size depends on how accurately landers land. Landing aids and terrain-relative navigation shrink the landing ellipse and the pad1. Open Moon puts a radio beacon at the centre and lights and reflectors on the edge. This is a design choice; no pad aids have flown.

Inspection. NASA’s SCALPSS stereo cameras imaged a real landing on Blue Ghost Mission 1 in 20256. NASA is now using them in vacuum-chamber plume tests to measure craters, the ejecta sheet angle and particle speeds5. Open Moon puts the same kind of cameras on each berm.

Sizing

Item Pad 1 Pad 2 Basis
Fused core diameter 30 m 50 m Design choice
Core area 707 m² 1,963 m² π × r²
Thickness 50 mm 50 mm Design choice, within NASA’s 25–50 mm study range1
Fused volume 35 m³ 98 m³ area × 0.05
Fused mass ~95 t ~265 t × 2.7 t/m³9
Polymer for same pad — ~35 t NASA table, 50 m at 50 mm1

NASA’s Artemis pad requirement was 200 m across. NASA’s landing experts were working to cut it to 100 m1. Pad 2’s compacted apron reaches 100 m for that reason. A polymer-only pad would need far more than the ~2 t of binder in the M05 budget. So polymer is kept for grout and repairs.

Testing and qualification

  1. Coupon hot-fire tests of fused samples and grouted pavers, as in the NASA/Masten campaigns1.
  2. Vacuum plume tests on a fused test bin at NASA Langley-type facilities5.
  3. Full-size paver section on Earth, built by the same robots, then thermal-cycled.
  4. Pad 1 on the Moon: a small lander lands on it. Cameras and witness plates measure ejecta. Lidar scans for damage.
  5. Pad 2 is cleared for heavy landers only after pad 1 data match the models.

Open questions

  • What plume pressure and temperature will heavy landers put on the pad, and at what height?
  • Is a continuous fused slab or a paver field better under thermal cycling?
  • Which landing aids will lander providers actually use?
  • How far must the berm sit from the pad edge to catch most spray?
Problems and solutions · 7
SeverityProblemSolution
CriticalNo fused pad has been tested under a full-size lander engine, on Earth or the MoonBuild pad 1 first and use it only for small landers; measure; scale up step by step before any heavy lander.
CriticalHeavy landers land with a large error; NASA's Artemis pad requirement was 200 m acrossWork with lander providers to cut the ellipse to about 100 m with beacons and terrain-relative navigation; keep pad 2's apron to 100 m.
HighHot-fire tests eroded pavers under the most extreme thermal conditionsThicker centre zone; replaceable centre pavers; inspect and repair after every landing.
HighLunar regolith compacts less than simulants, so the base may settle and crack the surfaceUse M01 geotechnical data; test compaction on site before sintering; leave expansion joints.
HighPolymer binder must be shipped from Earth; a 50 m polymer pad needs about 35 tUse local fused regolith for the pad; keep polymer for grout and repairs only.
MediumThermal cycling may crack a large fused slabBuild in pavers or panels with grouted joints rather than one slab.
MediumLanding aids on the pad edge can be damaged by the plumeMount lights low behind the berm crest; make beacons cheap and replaceable.

Specification

Quantity2 pads (plan design choice)
Pad 130 m sintered core, small and medium landers (design choice)
Pad 250 m sintered core plus compacted apron to 100 m, heavy landers (design choice)
Surface thickness50 mm fused regolith (design choice; NASA study range 25–50 mm)
Surface mass~95 t (pad 1) and ~265 t (pad 2), all local regolith (ESTIMATE)
Berm~2 m high ring around each pad (ESTIMATE)
Landing aidsBeacons, lights and reflective markers on the pad edge
InspectionStereo cameras and witness plates at every landing
Material from EarthPolymer grout for repairs only, under 2 t
Technology readiness · TRL 4 / 9

Sources

  1. Gelino et al., NASA KSC: In-situ lunar launch and landing pad construction with regolith-thermoset polymer composites (2022)
  2. NASA: NASA tests landing pad materials for future lunar missions (Oct 2021)
  3. Gelino et al., NASA KSC: Lunar landing and launch pad construction, concepts and criteria (2020)
  4. NASA NTRS 20120000029: Further analysis on the mystery of the Surveyor III dust deposits (2012)
  5. NASA: NASA begins Moon mission plume-surface interaction tests (Aug 2026)
  6. NASA NTRS 20250010922: SCALPSS 1.1 post-landing terrain measurements (2026)
  7. PISCES: PISCES completes lunar landing pad bullseye (Jan 2016)
  8. Effinger, NASA MSFC: Microwave sintering lunar landing pads and horizontal infrastructure (MMPACT) (Dec 2020)
  9. ICON: Project Olympus, LSIC slides (Jan 2024)
  10. Connolly and Carrier, LPSC 2023: Updating lunar subsurface geotechnical properties (2023)
ProjectOPEN MOON · Self-sustaining lunar colony
DocumentC05.2
Revision1.2 · Draft
EditEdit on GitHub