Vertical solar array towers
Mast and deployer
Lifts the arrays at least 10 m above the ground, and can lower them again for a move.
- Telescoping box sections, rolled lenticular boom or helical metal band
- Winch or roller deployer
- Mast root fitting
- Retraction drive
- Load and position sensors
Solar array blankets
Flexible solar blankets that roll or fold out along the mast.
- Triple-junction cells (30.7% XTJ Prime class)
- Flexible blanket substrate
- Roll-out composite booms (ROSA)
- Blanket harness
- Cover glass and coatings
Gimbal and sun tracking
Keeps the mast plumb and turns the arrays to follow the low polar Sun.
- Two-axis levelling actuators
- Azimuth rotator with slip ring
- Sun sensors
- Inclinometer
- Pointing controller
Base and lander interface
Holds the tower on rough ground and gets it off the lander.
- Tripod or sled base with levelling legs
- Launch locks
- Offload interface (self-propelled or towed cart)
- Ballast or ground anchors
- Grid cable connector
Power electronics and night survival
Conditions array power for the grid and keeps the tower alive in the dark.
- Maximum-power-point converters
- Grid interface converter (UMIC class)
- Survival battery
- Heaters and thermostats
- Avionics and radio
Dust protection
Limits dust build-up on the cells, mechanisms and radiators.
- Electrodynamic dust shield on cells
- Mechanism seals
- Radiator coatings
- MLI enclosure for electronics
What it does
At the south pole the Sun skims the horizon, so hills and crater rims cast very long shadows. A tall tower lifts its arrays out of those shadows and catches more hours of sun1. On the Shackleton connecting ridge, the best point is lit 92% of the time at 2 m height and 96% at 10 m10. Each tower turns that sunlight into 10 or 50 kW for the grid. The towers can also be lowered and moved1.
How it works
- Mast. NASA’s reference design needs at least 10 m from the ground to the bottom of the arrays. It uses 36 m² of array and is about 16 m tall when deployed, built from six telescoping segments of about 3 m each4. The three industry prototypes use different masts3:
- Lockheed Martin: a rolled lenticular boom.
- Honeybee Robotics: a helical metal band.
- Astrobotic: a ROSA-based mast on a self-propelled cart.
- Blankets. Redwire’s ROSA roll-out arrays have flown on the ISS since 2017. Each iROSA wing gives more than 28 kW from 30.7%-efficient cells8. Astrobotic’s towers use ROSA35.
- Tracking. A gimbal makes the mast plumb on slopes of up to 15° and turns the arrays toward the Sun. A slip ring lets it rotate continuously4.
- VSAT-XL. Astrobotic’s 50 kW tower is 34 m tall and 12.5 m wide5. It tracks the Sun, levels itself, and is designed to sit on top of the Griffin lander6. A NASA SBIR Phase II contract runs from June 2025 to June 20277.
- Dust and night. Some designs add NASA’s electrodynamic dust shield3. The towers must survive 96 hours of darkness and last up to ten years2.
Sizing
- 10 kW tower (ESTIMATE). Sunlight carries 1,361 W/m²13. 36 m² × 1,361 W/m² × 0.307 ≈ 15 kW at the cells. A combined factor of about 0.67, for cell packing, heat, pointing and wiring losses, gives 10 kW.
- 50 kW tower (ESTIMATE). 50 kW ÷ (1,361 × 0.307 × 0.67) ≈ 180 m² of array.
- Fleet (plan design).
| Item | Number | Peak power | Mass (ESTIMATE) |
|---|---|---|---|
| 10 kW tower | 2 | 20 kW | ~2 t |
| 50 kW XL tower | 2 | 100 kW | ~6 t |
| Total | 4 | 120 kW | ~8 t |
- Why several ridges. Two points about 8 km apart on a Shackleton ridge are lit a combined ~94% of a lunar year11. Shadows of up to about 100 hours remain12, so fission and storage still carry the night.
Testing and qualification
- Ground prototypes. Honeybee Robotics and Astrobotic tested their prototypes in JSC’s Chamber A in summer 2024; the chamber reaches 20 K2. Astrobotic’s tower was tested for stability, gimbal action and sun tracking on regolith simulant in NASA Glenn’s SLOPE facility9.
- Life cycling. Deploy and retract each tower many times in cold vacuum. Run the gimbal for a 10-year equivalent number of turns.
- Dust and slope. Run full-height deployments on a 15° simulant slope, and blast samples with dust from simulated landings.
- Flight demo. NASA’s VSAT project has argued for a flight demonstration around 2028–20293. The first Open Moon 10 kW tower could fill that role.
- On the Moon. Measure power against predicted illumination for one full year before relying on the tower for essential loads.
Open questions
- What is the real flight mass of a 10 kW tower and of the XL?
- Which ridge points give the least overlap in shadow time for the actual landing site?
- Should the XL be a fixed tower (Astrobotic 2025) or have a mobile version (Astrobotic 2024)56?
- How fast do cells degrade from dust, radiation and thermal cycling over 10 years at the pole?
- Should towers output DC straight into the ±4 kV grid, or high-voltage AC as Astrobotic proposed3?
| Severity | Problem | Solution |
|---|---|---|
| High | Even at 10 m, the best single point is in shadow 4–8% of the time. | Spread towers over two or three ridge points that are shadowed at different times; back them up with fission (C04.1) and storage (C04.3). |
| High | Tall masts can buckle or tip on slopes or soft regolith. | Use active plumbness control and wide levelling legs; test full-height towers on regolith simulant slopes before flight. |
| High | All prototype designs were above their mass goals at preliminary design. | Budget ~1 t per 10 kW tower now (ESTIMATE); fly the 10 kW towers first and learn before buying the XL. |
| High | Dust thrown up by landers can sandblast and coat the arrays. | Keep towers 1 km+ from landing pads (M05); vertical blankets shed falling dust; electrodynamic dust shields. |
| Medium | VSAT-XL is still a ground prototype of the deployment system only. | Treat the 50 kW towers as step 3 of the build; keep an option to fly four more 10 kW towers instead. |
| Medium | Mechanisms may jam in deep cold when retracting for a move. | Thermal-vacuum cycle every mechanism at worst cold; carry spare motors; design so a stuck tower still makes power where it stands. |
| Medium | No flight demonstration of a vertical lunar array is funded yet. | Push for the flight demo NASA's project has proposed for 2028–2029, or fly the first Open Moon 10 kW tower as that demo. |
Specification
| Power | 10 kW (VSAT) and 50 kW (VSAT-XL) per tower |
| Height | ≥10 m to bottom of arrays, ~16 m total (10 kW); 34 m (XL) |
| Array area | 36 m² (10 kW); ~180 m² (XL, ESTIMATE) |
| Cells | Triple-junction, ~30% efficient |
| Mass | ~1 t per 10 kW tower; ~3 t per XL tower (ESTIMATE) |
| Slope | Up to 15° at set-down, self-levelling |
| Life | 10 years at the south pole |
| Night survival | ≥96 h in darkness |
| Quantity | 2 × 10 kW + 2 × 50 kW on 2–3 ridge points |
| Delivery | Small landers (10 kW); medium lander such as Griffin (XL) |
Sources
- NASA RELEASE 22-090: Vertical Solar Array Technology awards (Aug 2022)
- NASA: From Houston to the Moon, Johnson's thermal vacuum chamber tests lunar solar technology (2024)
- NASA GCD: Vertical Solar Array Technology project annual review (Sep 2023)
- Belbin, Mills & Chan, NASA LaRC: Government Reference Design of the VSAT Demonstrator (Apr 2024)
- Astrobotic: awarded lunar power study with VSAT-XL (Aug 2024)
- Astrobotic: developing XL solar array tech for lunar power infrastructure (Jul 2025)
- Contract record 80NSSC25C0032: Astrobotic VSAT-XL SBIR Phase II (Jun 2025)
- Redwire: second pair of iROSA solar arrays delivered (Jun 2022)
- SatNews: Astrobotic's LunaGrid VSAT enters thermal vacuum testing (press) (Jul 2024)
- Gläser et al. 2014, Icarus: Illumination at the lunar south pole (2014)
- Wikipedia: Peak of eternal light (2026)
- Csank & Scott, NASA GRC: Power and Energy for the Lunar Surface (Apr 2022)
- Wikipedia: Solar constant (2026)